航線填本常用語句范例
……檢查發現/報告故障……
1. 航后：檢查發現左后航行燈不亮。
After Flight(AF )：Find L AFT position light is not on.
2. 檢查發現右前輪磨損超標。
Check R tire of the nose landing gear is worn out of limits.
3.  檢查發現2號ATC故障。
Check ATC system No.2 ATC fails.
4. 檢查發現左外剎車組件磨損超標。
Check L outboard wear indicator pin of MLG brake assy is out of limits.
航后檢查發現：(AF Check)
AF Check ：Check L outboard wear indicator pin of MLG brake assy is out of limits.
Accomplish Task Card：TZ-AF-03，check L outboard wear indicator pin of MLG brake assy is out of limits.
過站檢查發現：(TR check)
TR check : Check L outboard wear indicator pin of MLG brake assy is out of limits.
Accomplish Task：TZ-TR-00，Check L outboard wear indicator pin of MLG brake assy is out of limits.
5. 檢查發現左主起落架一液壓管漏油超標。
Check the L MLG hydraulic tube leakage is out of limits.
6. 檢查發現13B座位小桌板不能收起，無法保持在收上位。
Check the NO.13B passenger tray table could not be stowed and hold on the stow position.
Accomplish Task：：xx-xx-xx，Check the NO.13B passenger tray table could not be stowed and hold on the stow position..（完成xx-xx-xx工卡發現…）
AF Check ：Check the NO.13B passenger tray table could not be stowed and hold on the stow position（航后檢查發現…）
TR check : Check the NO.13B passenger tray table could not be stowed and hold on the stow position（過站檢查發現…）
7．機組報告空中右發燃油濾旁通燈亮。
The flight crew reported right engine Fuel FILTER BYPASS Light came on in flight.
8. 航后APU自檢有49-41012故障信息.
AF Check: maintenance message 49-41012 is displayed after APU BITE.
9. 前洗手間“有人、無人”標牌松動。
The “None/Occupied” placard in forward lavatory is loosening.

參考/按..更換（件）……，檢查 / 測試正常
1. 過站：根據AMM32-45-21更換右前輪，并根據AMM 12-15-51/301檢查輪胎氣壓正確。
TR Check：Refer to AMM32-45-21 to replace the R nose wheel，and refer to AMM 12-15-51/301 to check the tire pressure，ensure the tire pressure is normal.
2. 根據AMMXX-XX-XX更換2號ATC收發機，并根據AMMXX-XX-XX對系統完成測試，結果正常。
Refer to AMMxx-xx-xx to replace the No.2 ATC transceiver，and Refer to AMMxx-xx-xx to do a system function test，the result is normal.
3. 航后根據AMM49-41-11更換APU起動機，啟動測試APU工作正常。
AF: Refer to AMM49-41-11 to replace the APU starter，start APU and do an operation test，the result is normal.
4. 過站根據AMM25-22-00折下第三排ABC座椅，座椅隨機放在前貨艙。
TR：Refer to AMM25-22-00 to remove the passenger seats 3A/3B/3C，and leave in the FWD cargo compartment.
5. 根據工卡XXXX，更換時控件電瓶，根據AMMXX-XX-XX測試電瓶電壓為XX伏，符合手冊要求。
Refer to task card xxxx to replace the time control battery，AMMxx-xx-xx to test the voltage is XX volt，and satisfy to AMM requiements..
檢查發現…故障，按…保留，…號/類別，同意放行
1. 過站檢查發現前服務話筒失效，按MEL23-20放行飛機。
TR Check: Find the FWD attendant handset failed，refer to MEL23-20 to dispatch.
Accomplish Task card：TZ-TR-00，F(xiàn)ind the FWD attendant handset failed，refer to MEL23-20 to dispatch..
2. 航后檢查發現右發PRSOV失效，因航材無料，根據MEL36-5完成M項工作，將右發PRSOV鎖關位放行，在右發引氣電門處貼不工作標牌，并辦理保留DD3000000。
AF Check: Find the R engine PRSOV failed. Accomplish maintenance (M) items per MEL36-5 and lock the PRSOV in close position prior dispatch due to lacking of spare parts. Paste the“R ENGINE BLEED AIR SYSTEM INOP”tag next to the R engine bleed air switch，The deferred defect form NO. is DDXXXXXXX.
按…，更換…件，測試正常，撤消 / 關閉…保留
1. 航后依據AMM23-20-00，更換前服務話筒，并完成功能測試結果正常，撤消DD/FCXXXXX。